PA Parting out a 72 blazer - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**dutchmanz** · 06-25-2014, 12:38 PM

I'll take those rear seatbelts if you still have them.

**1rippen6** · 06-25-2014, 12:43 PM

dutchmanz belts still available pm sent

**1rippen6** · 06-25-2014, 07:12 PM

tjsblazer I checked 3 frames it appears there is one long one and one short one on a crossmember if that is correct 25 for the pair plus shipping let me know.

**1rippen6** · 06-25-2014, 07:13 PM

gpat@earthlink.net does not look bad will get a picture tomorrow and mark where I think you want it cut and you can confirm. Just so we are on the same page passenger side correct?

tjsblazer · 06-25-2014, 11:21 PM

Quote:

Originally Posted by 1rippen6

tjsblazer I checked 3 frames it appears there is one long one and one short one on a crossmember if that is correct 25 for the pair plus shipping let me know.

That sounds right to me. Can you pm or post me a quick pic just to be sure. I will take them if they check out ok.

**1rippen6** · 06-26-2014, 08:33 AM

tjsblaser will get you pictures tonight

**1rippen6** · 06-26-2014, 09:13 AM

gpat@earthlink.net attached is a photo of the a pillar with red lines where to cut if I understood you correctly. 40 plus shipping if still interested I will cut the windshield out and make sure it looks ok underneath the rubber. Let me know.

**1rippen6** · 06-26-2014, 09:14 AM

correct picture

**1rippen6** · 06-27-2014, 06:22 AM

Pictures for tjsblazer

69-72 · 06-27-2014, 08:22 AM

Do yo happen to have the gas tank straps?

**1rippen6** · 06-27-2014, 09:19 AM

Yes the gas tank is still in it I will try and remove tonight and post some pictures of the straps. If not tonight then sometime this weekend.

69-72 · 06-27-2014, 09:35 AM

Actually I found a bought a minty set just after I posted. I am sure someone else will want them though, the repro straps are junk. Thanks anyways.

**1rippen6** · 06-27-2014, 10:13 PM

No problem just glad you left me know before I pulled it. Thanks

tjsblazer · 06-30-2014, 09:56 PM

Quote:

Originally Posted by 1rippen6

Pictures for tjsblazer

Those are the brackets but they seem pretty corroded. Not sure how a blast would leave them. I think I'll hold off for now. Thank you.

**1rippen6** · 06-30-2014, 10:00 PM

No problem I think they would be fine blasted but you call thanks for letting me know.

BigCarl · 07-02-2014, 01:37 PM

I need the passenger side bracket for the park brake equilizer. Its a little further forward than mid-frame and is next to the transfer case and has 2 rivets attaching it to the frame ride behind the passenger side exhaust hanger bracket.

Let me know, please.

**1rippen6** · 07-02-2014, 03:20 PM

Will check tonight if it is not raining.

**1rippen6** · 07-03-2014, 06:14 PM

Pic for BigCarl this is on the drivers side I do not have anything on the passenger side but a ebrake hanger which is just a rod with bent ends

**1rippen6** · 07-24-2014, 07:46 AM

ttt

jthomass · 07-29-2014, 06:54 PM

Wondering if the 4 inch lift is still for sale? Thanks

**pimpston65** · 08-06-2014, 02:09 PM

Quote:

Originally Posted by 1rippen6

ttt

is that roof rack still available?

**1rippen6** · 08-06-2014, 02:33 PM

Yes it is

**pimpston65** · 08-06-2014, 02:40 PM

Quote:

Originally Posted by 1rippen6

Yes it is

i saw the hold down were twek'd are the busted? also send pics of the gearbox!!!

**1rippen6** · 08-06-2014, 02:49 PM

They are cracked but not in two pieces they are definitely not perfect. I do have another roof rack if interested not sure of the shape of that one either. I can get better pictures of both roof racks and the steering box tonight.

mgkgmc · 08-06-2014, 03:55 PM

Does it have a gas tank skid plate? If so I might be interested.

06-25-2014, 12:38 PM	#51
dutchmanz Knuckle Buster, Instructor Join Date: May 2010 Location: Pantego, NC Posts: 562	Re: Parting out a 72 blazer I'll take those rear seatbelts if you still have them. __________________ Current classic fleet: 72 K5 Blazer CST, unrestored factory Orange paint...mostly 69 C10 factory SWB, 454, TH400, Saddle tan, Rust-o-ration 53 Studebaker M35 w/331 Reo gas I-6, Air Force Strata Blue

06-25-2014, 12:43 PM	#52
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer dutchmanz belts still available pm sent

06-25-2014, 07:12 PM	#53
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer tjsblazer I checked 3 frames it appears there is one long one and one short one on a crossmember if that is correct 25 for the pair plus shipping let me know.

06-25-2014, 07:13 PM	#54
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer gpat@earthlink.net does not look bad will get a picture tomorrow and mark where I think you want it cut and you can confirm. Just so we are on the same page passenger side correct?

06-26-2014, 08:33 AM	#56
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer tjsblaser will get you pictures tonight

06-26-2014, 09:13 AM	#57
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer gpat@earthlink.net attached is a photo of the a pillar with red lines where to cut if I understood you correctly. 40 plus shipping if still interested I will cut the windshield out and make sure it looks ok underneath the rubber. Let me know. Attached Images

06-26-2014, 09:14 AM	#58
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer correct picture Attached Images

06-27-2014, 06:22 AM	#59
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer Pictures for tjsblazer Attached Images

06-27-2014, 08:22 AM	#60
69-72 Registered User Join Date: May 2008 Location: 204 Posts: 903	Re: Parting out a 72 blazer Do yo happen to have the gas tank straps? __________________ 1969 Chevy Custom Camper 3/4 ton Rust free survivor 1972 Chevy Blazer CST 4x4 Almost Rust free survivor 1972 GMC Jimmy 2wd Undergoing surgery

06-27-2014, 09:19 AM	#61
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer Yes the gas tank is still in it I will try and remove tonight and post some pictures of the straps. If not tonight then sometime this weekend.

06-27-2014, 09:35 AM	#62
69-72 Registered User Join Date: May 2008 Location: 204 Posts: 903	Re: Parting out a 72 blazer Actually I found a bought a minty set just after I posted. I am sure someone else will want them though, the repro straps are junk. Thanks anyways. __________________ 1969 Chevy Custom Camper 3/4 ton Rust free survivor 1972 Chevy Blazer CST 4x4 Almost Rust free survivor 1972 GMC Jimmy 2wd Undergoing surgery

06-27-2014, 10:13 PM	#63
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer No problem just glad you left me know before I pulled it. Thanks

06-30-2014, 10:00 PM	#65
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer No problem I think they would be fine blasted but you call thanks for letting me know.

07-02-2014, 01:37 PM	#66
BigCarl Registered User Join Date: Sep 2007 Location: Thunder Bay, Ontario Posts: 170	Re: Parting out a 72 blazer I need the passenger side bracket for the park brake equilizer. Its a little further forward than mid-frame and is next to the transfer case and has 2 rivets attaching it to the frame ride behind the passenger side exhaust hanger bracket. Let me know, please.

07-02-2014, 03:20 PM	#67
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer Will check tonight if it is not raining.



Register or Log In To remove these advertisements.

07-03-2014, 06:14 PM	#68
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer Pic for BigCarl this is on the drivers side I do not have anything on the passenger side but a ebrake hanger which is just a rod with bent ends Attached Images Last edited by 1rippen6; 07-03-2014 at 06:16 PM. Reason: forgot to add info

07-24-2014, 07:46 AM	#69
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer ttt

07-29-2014, 06:54 PM	#70
jthomass Registered User Join Date: Aug 2010 Location: Fargo, ND Posts: 51	Re: Parting out a 72 blazer Wondering if the 4 inch lift is still for sale? Thanks

08-06-2014, 02:33 PM	#72
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer Yes it is

08-06-2014, 02:49 PM	#74
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,710	Re: Parting out a 72 blazer They are cracked but not in two pieces they are definitely not perfect. I do have another roof rack if interested not sure of the shape of that one either. I can get better pictures of both roof racks and the steering box tonight.

08-06-2014, 03:55 PM	#75
mgkgmc Registered User Join Date: Dec 2007 Location: Glendale Arizona Posts: 1,354	Re: Parting out a 72 blazer Does it have a gas tank skid plate? If so I might be interested. __________________ 1970 GMC 1500 stepside 1972 GMC Jimmy Custom 2004 Chevy Colorado 1989 Swb Silverado 1972 Aj's Stormer

Register or Log In To remove these advertisements.