"Elwood" the 77_remix

[N2TRUX]

Originally Posted by BB72CHEVKT

I like the new wheels so much I think I need a pair for my new to me 83. Any idea when they can be purchased and price point.

You will need to contact your local Wheel Pro dealer. They can give you info on pricing and availability.

[N2TRUX]

Friday night shop session was focused on the rear axle. I wanted to pull it to clean it up a bit. The stock shock mounts were still attached, and the pinion seal is seeping.

I had preciously removed most of the 4 link and set it aside. I finished removing some components and disconnected the E brake cable and brake line.

I pulled the inspection cover and drained the gear oil. While that was off, I tested the fit of the Moser Engineering differential cover. I was concerned that the panhard bar mount might create a conflict, and it does. I'll address that issue later.

[N2TRUX]

With the 12 bolt on the ground i was able to slide it out from under the truck. I recall removing the bottom shock mounts from Scarlett while laying on my back. I decided to do it standing up on Elwood.

After a few minutes with a cut off wheel, followed by a flapper disc the axle was cleaner looking. I plan to make new brake lines and replace the rubber with braided stainless. I am working with Wilwood to determine what brakes I will run. That will decide how the lines are laid out.

Time constraints wont allow me to change gears and add a locker. My 3.08 one wheel peel differential will have to do for now.

[N2TRUX]

Originally Posted by N2TRUX

...Time constraints wont allow me to change gears and add a locker. My 3.08 one wheel peel differential will have to do for now.

Looks like there might be a change in plans. I located a 10 bolt with 3.42 gears locally. I'm supposed to pick it up later today.

I was sick over the Thanksgiving weekend so i didnt get any shop time. I manged to finish my work on Friday but that was about it. Saturday was bad and Sunday I slept all day.

I'm somewhat better today, so I'll be doing updates later.

[rustytruck50]

Hooked & reeled in Ken! Elwood is spot on in so many ways

[N2TRUX]

Originally Posted by rustytruck50

Hooked & reeled in Ken! Elwood is spot on in so many ways

Come on in and enjoy the show.

[gringoloco]

I like my stainless magnaflows, but with the small block, they can get a little glass-packy. Brrraaaap!

[N2TRUX]

Originally Posted by smpoulin01

I believe that will be a great choice!

Originally Posted by gringoloco

I like my stainless magnaflows, but with the small block, they can get a little glass-packy. Brrraaaap!

I hope it has a good sound. I'm going to run as much tailpipe as possible to clean it up.

[N2TRUX]

I received a batch of goodies from Deeds Engineering yesterday. I would normally say the pics dont do them justice. In this case Kevin has some fantastic photos on his website and the finished product looks just as nice. These definitely are multi level up in quality over standard exhaust components.

[Bloodhound]

Wow those are nice. Trying to picture how they bolt up.

[N2TRUX]

Originally Posted by Bloodhound

Wow those are nice. Trying to picture how they bolt up.

The V bands are a three piece component. There are two rings that slide over the exhaust pipe. The outer band clamps around both rings and clamps them together to create a seal.

Those flat tabs are weld to the exhaust system. The "dogbones" are captured between the tabs. They have a built in bushing to absorb some of the vibration. There are additional hangers that will be utilized as we get the system laid out.

[Bloodhound]

Very cool.

[N2TRUX]

A swing, and a miss. I got my exhaust parts from Summit today. I wanted to test fit everything to see how it fit. Yikes! I was not even close. In my defense, its not easy trying to lay on your back, hold parts in place, and measure what you need.

I ordered a 10" Flex fitting and its way too long. I wanted as much flex as possible but a 6" tube will have to suffice. I mistakenly pulled the Magnaflow part number for a offset/offset muffler. Instead I need a center/offset to work.

Fortunately Summit has an excellent return policy. Since the parts weren't installed, they emailed me a prepaid return label. As soon as they see that I shipped the parts they will process my new parts. Thanks Summit!

[STOCKISH]

Everything looks fantastic as usual! Can’t wait to see that interior finished up!

[N2TRUX]

It really sucked not being able to put in shop time this weekend. I'm trying to shake a respiratory infection and I find the best cure is sleep. Consequently I was rather depressed today after a much needed weekend past by.
Fortunately I received some pics today from Brent at Sculpt Garage He is almost finished with the seat for Elwood. I wanted to wait till I picked it up to post pics, but I cant. I'm really pleased with the results.

The insert material is OEM for earlier squares, and the red emulates the 1977 grain. Its a brighter red by Enduratex in the Oxen series. Its a bit brighter than what I wanted but so far everyone I show it to likes it better than my choice.

Lets see what the critics think?

[STOCKISH]

Spot on! Beautiful

[smpoulin01]

Looks really good!

[Coursey]

Where did you source the OEM material?

[ultrahd4me]

That's next level stuff for sure. Ken, yourself and Elwood is what has inspired a lot of us younger guys to get into the squarebody trucks. This definitely raises that bar to another level. Killer work as usual sir.

[N2TRUX]

Originally Posted by ultrahd4me

That's next level stuff for sure. Ken, yourself and Elwood is what has inspired a lot of us younger guys to get into the squarebody trucks. This definitely raises that bar to another level. Killer work as usual sir.

Bobby that means a lot my friend. My hope is to show that persistence can produce a quality build with a fair budget in an average back yard shop.

[aggie91]

The new seat looks great! I really do like the red you used!

Can't wait to see Elwood in February.

[N2TRUX]

Originally Posted by STOCKISH

Spot on! Beautiful

Originally Posted by smpoulin01

Looks really good!

Originally Posted by Coursey

Where did you source the OEM material?

Originally Posted by aggie91

The new seat looks great! I really do like the red you used!Can't wait to see Elwood in February.

Thanks guys. I'm trying to stay true to the original truck with some pleasing updates. The OEM material came from SMS Auto fabrics They have the best selection and are very knowledgeable on their inventory. I was apprehensive about using 40 year old vinyl until I got the sample. It still had that "new car" smell to it.

[gringoloco]

Are you wrapping or painting the rest of the interior? Hard to beat red guts on black

[N2TRUX]

Originally Posted by gringoloco

Are you wrapping or painting the rest of the interior? Hard to beat red guts on black

The bottom of the dash will be painted. The dashpad and plastic trim parts will be dyed. I dont think I'm going to paint the back of the cab red as depicted. That opens up a can of worms with no real stopping point.

[rustytruck50]

Wow...that's really going to look great with the black!